Elice pentru exterior VEVOR cu 3 pale 13,25 x 17

Brand:VEVOR

3.5/5

L
804.59

Aliaj robust de aluminiu: suporturile noastre de viteză pentru exterior rezistente la coroziune sunt fabricate din aliaj de aluminiu și construite pentru a dura. Are o rezistență la tracțiune de 260-300 MPA, făcându-l rezistent la rugină și deformare, chiar și sub apă de mare și apă dulce. Butuc de cauciuc îmbunătățit: elicea motorului exterior este construită cu un butuc de cauciuc și 13 caneluri dinți. Butucul rezistent la uzură are, de asemenea, un efect puternic de amortizare, conceput pentru amortizarea și protejarea trenului de transmisie de majoritatea șocurilor. 13 1/4 Diametru x 17 Pas: Cele două măsurători principale ale elicei unei bărci sunt diametrul și pasul. Pasul este distanța teoretică pe care o elice se va deplasa prin apă în timpul fiecărei revoluții, iar diametrul este distanța de-a lungul unui cerc care cuprinde toate paletele elicei. Cu 13 1/4 diam. x 17 pas, elicea noastră exterioară a bărcii se va asigura că nava dumneavoastră se deplasează fără probleme și rapid. Forță puternică și propulsie stabilă: elicea bărcii noastre poate strânge rapid vortexul, oferind o forță puternică pentru propulsia navei. Designul unic al lamei elicelor permite ambarcațiunii dumneavoastră să accelereze mai repede și vă permite să controlați mișcarea în apă cu o mai mare precizie. Este potrivit pentru diverse activități de recreere în apă - de la distracția în familie până la competiții sportive, aducând mai multă bucurie schiului nautic. Înlocuire directă: 13 1/4 diam. Elicea exterioară cu pas de 17 este compatibilă cu motorul Evinrude în 2 timpi de 40-140 CP, înlocuind direct OEM 765183. Elicea bărcii noastre se bazează pe rotirea palelor în apă pentru a converti puterea de rotație a motorului în propulsie, ceea ce se va potrivi bine cu barca dumneavoastră. .

Nu există unități disponibile
Aliaj robust de aluminiu: suporturile noastre de viteză pentru exterior rezistente la coroziune sunt fabricate din aliaj de aluminiu și construite pentru a dura. Are o rezistență la tracțiune de 260-300 MPA, făcându-l rezistent la rugină și deformare, chiar și sub apă de mare și apă dulce. Butuc de cauciuc îmbunătățit: elicea motorului exterior este construită cu un butuc de cauciuc și 13 caneluri dinți. Butucul rezistent la uzură are, de asemenea, un efect puternic de amortizare, conceput pentru amortizarea și protejarea trenului de transmisie de majoritatea șocurilor. 13 1/4 Diametru x 17 Pas: Cele două măsurători principale ale elicei unei bărci sunt diametrul și pasul. Pasul este distanța teoretică pe care o elice se va deplasa prin apă în timpul fiecărei revoluții, iar diametrul este distanța de-a lungul unui cerc care cuprinde toate paletele elicei. Cu 13 1/4 diam. x 17 pas, elicea noastră exterioară a bărcii se va asigura că nava dumneavoastră se deplasează fără probleme și rapid. Forță puternică și propulsie stabilă: elicea bărcii noastre poate strânge rapid vortexul, oferind o forță puternică pentru propulsia navei. Designul unic al lamei elicelor permite ambarcațiunii dumneavoastră să accelereze mai repede și vă permite să controlați mișcarea în apă cu o mai mare precizie. Este potrivit pentru diverse activități de recreere în apă - de la distracția în familie până la competiții sportive, aducând mai multă bucurie schiului nautic. Înlocuire directă: 13 1/4 diam. Elicea exterioară cu pas de 17 este compatibilă cu motorul Evinrude în 2 timpi de 40-140 CP, înlocuind direct OEM 765183. Elicea bărcii noastre se bazează pe rotirea palelor în apă pentru a converti puterea de rotație a motorului în propulsie, ceea ce se va potrivi bine cu barca dumneavoastră. .
Brand VEVOR
Brand ‎VEVOR
Brand Name ‎VEVOR
Color Black
Color ‎Black
Customer Reviews 4.5 4.5 out of 5 stars 149 ratings 4.5 out of 5 stars
Engine Type 2 Stroke
Engine Type ‎2 Stroke
Included Components ‎1 x Nut, 1 x Outboard Propeller, 1 x Split Pin
Item Dimensions LxWxH ‎13.25 x 7.1 x 13.25 inches
Item Package Dimensions L x W x H ‎14.96 x 14.96 x 7.05 inches
Item Weight 7 Pounds
Item Weight ‎7 Pounds
Manufacturer ‎VEVOR
Material Aluminum
Material ‎Aluminum
Model Name ‎Replace for OEM 765183, Compatible with 45-140HP Outboard Johnson Evinrude Engine
Mounting Type ‎Engine
Number of Items ‎1
Package Weight ‎3.39 Kilograms
Part Number ‎3 Blades 13 1/4" x 17" Boat Propeller
Recommended Uses For Product ‎For Sport Utility Vehicles
Size ‎13.25" x 17"
Style ‎3-Blade
Suggested Users ‎unisex-adult

3.5

13 Review
5 Star
75
4 Star
11
3 Star
5
2 Star
1
1 Star
7

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu*

Scritto da: Caleb M.
I have no confidence in this product
It looks pretty close to the original spitfire prop, however... I ran into problems while installing it. I will say that I have not used this in the water yet and will be trying it out this weekend if everything goes well. That said, once I can get a new Mercury Prop this thing is going into a storage bin just for a backup. Problem 1 while installing it: The Hub doesn't fit inside the prop. It says "it should slide 3/4 of the way in and then you can push or gently tap" the rest of the way. That was 100% untrue. I had to get a big socket and a rubber mallet and beat that thing in there. Even then I had to tighten the nut down on the prop to get it to seat far enough in for the outer washer to lock onto the splines. I didn't feel good about doing this at all. Problem 2: The picture... After I tightened it down to seat everything I took it apart and put that lock washer on. I tightened the prop nut down to 55 ft-lbs as instructed by Mercury. The lock washer broke both pins off as you can see in the picture. I ended up using the old one and that held up fine. That is a HUGE problem in my eyes. I've had a prop fall off, not get knocked off, come undone and fall off almost 2 miles from the dock. I NEVER want to do that again. It's pretty unforgivable in my eyes, that's a key safety feature and they cheaped out on it. Problem 3 This may not be a problem but after I put it on, it didn't spin very freely while in neutral. I did start the engine up and put it in gear to let it spin and it now feels much better but I'm a bit worried about it. As long as it doesn't fall off this weekend I think we'll be ok. If this thing does have any problems getting the boat up on plane this weekend I'll update this. It looks very close to the mercury prop so I doubt that will be an issue and my main reason for not rating it higher is the terrible fit of the hub and them skimping out on a key safety feature. That lock ring is the cotter pin for those of you that have those on other engines. The one they provided was trash. ********* Update after using it: This is certainly not a "Great" replacement for a spitfire prop. Does it work? yes it certainly does. Is it the same as a mercury Spitfire prop? NOPE, not at all. It may not be a huge difference for everyone but my boat was noticeably slower to plane with this compared to the Mercury Spitfire that I had on it. I was still able to get around the same top speed, it took ages to get there though. Is it worth the price savings you get? For most people probably and I will keep it onboard as a spare just in case but I'll be getting a Mercury prop once I can find one closer to the normal prices. Right now they're about $70 more than what I paid 18 months ago.
Scritto da: vngstr
This is the best prop ever!!!
Tested two weekends ago!! Quick out of the chute, 2500rpm at 40mph, 1.5:1 mercruiser alpha 1 gen 2. could push 65-70. Purchased a second one as a backup... Awesome
Scritto da: james f
Fit great
Fit great would buy again
Scritto da: dennis rieker
having no problems. just as good as merc
works great went from three blade to a four way better haul shot.
Scritto da: Kevin Tran
Great value. Perfect replacement of the Mercury spitfire prop.
My first order went missing for a week. Amazon refunded and I reordered which arrived the next day. Bought it the replace the original Mercury Spitfire prop for my 2006 Mercury 60 hp four strokes outboard. The packaging was great with good instructions and all necessary components and even came with a nice pair white gloves. Prop is exactly the same dimensions as the previous Mercury spitfire that I replaced. All the components are brass alloy which I feel are even better than that of the Mercury spitfire prop which has a plastic splines. I have not yet tested out on the water yet but I have no reason to think that I will not perform as well as the original Spitfire. Will update on the performance later.
Scritto da: Randy Joseph
FANTASTIC PROP FOR THE MONEY
95% of the performance of my OEM Mercury Prop for one-third of the money. Highly Recommended.
Scritto da: Mark
Nut and Carter pin missing
Parts were missing otherwise looked like a great prop
Scritto da: Travis C.
You need a big washer or something
When installing you need a super flat hub washer so this sits flat on the shat if not the propeller will suck into the sterndrive within matter of minutes. If you try to use a standard hub washer it will barely fit threads and will wobble back towards the motor.
Scritto da: L. Briggs
Perfect
1988 Johnson 60HP outboard. Fits perfectly.
Scritto da: Shannon Maude
Fast delivery
Happy with the purchase. Fast delivery.
Scritto da: Glenn H Davies
Good quality, quick delivery
Propeller is good quality however it did not fit the hub on the prop shaft and another hub type had to be ordered which more or less doubled the price
Scritto da: King Francisco Z
Need to buy adapter for Mercruiser 3l but good pitch
NNED ADAPTER FOR MERCRUISER 3.O
Scritto da: mur ...
fast shipping
4 blades work well

Produse asemanatoare

hot

Descoperiți rețeaua noastră internațională

Expediem în 28 de țări, peste 200.000 de produse. Fii la curent, abonează-te la newsletter.

Array