Drill America 2-1/2 ferăstrău cu găuri cu vârf din carbură cu 1 adâncime de tăiere, seria CTH 1 adâncime de tăiere 2-1/2

Name: Drill America 2-1/2 ferăstrău cu găuri cu vârf din carbură cu 1 adâncime de tăiere, seria CTH 1 adâncime de tăiere 2-1/2
Brand: Drill America
SKU: 0887861226301
Price: 576.71 RON
Availability: InStock

Brand:Drill America

3.7/5

L
576.71

Dispozitivele de tăiere pentru găuri cu vârf din carbură Drill America CTH oferă o modalitate ușoară și eficientă de a găuri găuri cu diametru mai mare fără a necesita burghie mari și mandrine foarte mari. Sunt fabricate din oțel de mare viteză de calitate premium, cu dinți cu vârf de carbură pentru o durată de viață foarte lungă. Freze pentru găuri cu vârf din carbură frezele pentru găuri taie o gamă largă de materiale, cum ar fi oțel inoxidabil, fontă, fier, tablă și cupru. De asemenea, funcționează bine cu materiale abrazive precum rășina de înaltă densitate și plăcile metalice. Freza pentru găuri are o tijă de 1/2 și vine cu Pilot Drill și cheie hexagonală.

Cantitate

Adaugă in coş Cumpără acum

EAN: 0887861226301

Categorii Uneli și îmbunătățiri pentru casă, Unelte electrice și de mână, Piese și accesorii pentru scule electrice, Piese și accesorii pentru burghie electrice, Fierăstraie de găurit și accesorii, Fierăstraie pentru găuri,

Vine cu burghiu pilot, cheie hexagonală și melc cu ejectare automată. 1/2 tijă, 1' adâncime de tăiere. Tăiați o gamă largă de materiale, cum ar fi oțel inoxidabil, fontă, fier, tablă și cupru. Funcționează bine cu materiale abrazive precum rășina de înaltă densitate și plăcile metalice. Mod ușor și eficient de a găuri găuri cu diametru mai mare fără a necesita burghie mari și mandrine foarte mari. 2-1/2 diametru cu 1 adâncime de tăiere.

Brand	Drill America
Cutting Diameter	2-1/2" Inches
Finish Type	Uncoated
Is Discontinued By Manufacturer	No
Item model number	CTH2500
Manufacturer	Drill America
Material	Carbide-Tipped
Product Dimensions	6 x 4 x 4 inches; 15.87 Ounces
Shank Type	Hex

5 Star

4 Star

3 Star

2 Star

1 Star

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu^*

Rating-ul tău

Scritto da: Daryl B.

Excellent cutter!

This cutter gave a very smooth cut in 1/8" aluminum panel for my project! This is a large diameter size, so be cautious of the speed. My drill press was slowed to 700 rpm's. VERY PLEACED WITH THIS PRODUCT. Thanks, from Indianapolis.

Scritto da: caihu lemon

Cut quality

From now on this is the only brand I will use for hardened drill bits drilled 3/16 of 304ss

Scritto da: J W

Works great if used properly

Bought this for working with heavy steel, I have cut 3 holes through 1' mild steel and as many through 1/2'. It took some tuning to get the drill press dialed in, but at the proper speed and with some lubricant it does a nice job. On pieces thicker than 1/2 it works best to flip the metal over halfway through the cut to finish from the other side. Looks pretty much new after the 6 holes I've used it for, looking forward to using it on the next job.

Scritto da: shabbyjude

Best Cutter, but BEWARE

This is by far the best hole saw I have ever had over the last 50 yrs....the only negative is the quality control...after drilling 1 [ONE!!!!] hole, the set screw fell out...at least the screw had the courtesy to wait until the drill press stopped....so beware to check the set screws before using....I drilled a small relieve on the shaft so the set screw would not just be sitting on a flat area....then max lock tight on both screws....drilled 10+ more holes with 0 [ZERO] problems...that's why it gets a 5 star rating, unlike other hole saws with carbide tips that only manage to get thru a few uses...I am cutting thru 3/8'' plate steel and couldn't be happier....

Scritto da: APO

Heavy duty

The casing is 1/8" thick, 1" depth and heavy duty. Not like the other brand which casing is 1/16 thick. The picture shows shallow depth however it' 1" deep, compatible with Japanese product selling on MSC @ a higher price

Scritto da: Rich Bessom

Use at low RPMs with plenty of cutting oil.

I was very pleased with the operation of the 2-5/16" carbide tipped hole saw! I had to make 4 holes for the marker side lights on my vintage race car trailer that I'm rebuilding. I used it in an old 1/2" craftsmen hand drill motor. All the holes drilled very smoothly. The pilot drill worked great & didn't let the saw wander. The metal was 14 gauge steel, roughly a little thicker then a 1/16". The hole saw still looks brand new. It was shipped in a plastic protective container along with the Allan wrench for the pilot drill. It was well worth the money! I would recommend this tool! Thanks!

Scritto da: Jerry Sikes

Cut through body steel like a hot knife through butter

Following proper use recommendations to use cutting fluid to cool the tool and operating at a slow speed the tool surpassed all o my expectations and smoothly cut a clean precise hole even using it in a hand held drill. It is the best hole cutting bit I have ever used. I highly recommend this tool and have already purchased additional sizes. I am not a professional in a machine shop I use this at home.

Scritto da: PDGx

Fast and aggressive drill

Very aggressive hole saw/drill. Used on structural channel iron to pass 3.5” pipe through (3.5” drill size). Final hole does appear to be about a 64th small, but that is easy to correct. Just keep it lubed with cutting fluid.

Scritto da: Grant

Quality Product!

We use this product daily to add extra ventilation in our shipping containers. Quality product!

Scritto da: Sparkbing

Drill bit is garbage

Drill bit broke within seconds Can replace it nor does the seller have replacement bits

Scritto da: Becky Erickson

Five Stars

Good product.