Dremel 9901 Bit de sculptat din carbură de tungsten, 1/8” (3,2 mm) diametru, accesoriu rotativ pentru sculptură și gravare, freză de tăiere (1 bucată), argintiu

Brand:Dremel

3.7/5

L
141.87

DESCRIEREA PRODUSULUI Rain Bird PRF07530S Filtru de reglare a presiunii de 30 PSI pentru irigare prin picurare, filet tată 3/4. Protejați-vă componentele de irigare prin picurare din aval cu această unitate compactă de calitate profesională care combină filtrarea și reglarea presiunii într-o singură bucată. Prin reducerea numărului de componente într-o zonă de control; mai multe componente pot încăpea într-o singură cutie de supape. Cu mai puține conexiuni, instalarea este mai ușoară și mai rapidă. Mai puține piese și mai puține conexiuni filetate înseamnă, de asemenea, mai puține șanse de scurgere la instalare și pe durata de viață a sistemului. Unitatea de filtru reglează presiunea la 30 psi și capac cu inele O-ring de etanșare desfiletate pentru a oferi acces ușor la elementul de filtru cu ochiuri de 200 pentru curățare. Corpul și capacul robust sunt construite din polipropilenă umplută cu sticlă pentru rezistență, oferind o presiune de 150 psi. Funcționează cu toate supapele și vine cu un ecran din oțel inoxidabil de 200 de ochiuri (75 microni) preinstalat. Specificatii: 3/4 x 3/4 admisii filetate tata (MPT); interval de funcționare 0,20 până la 5,0 galoane pe minut; presiune de intrare 20 până la 150 psi. De asemenea, disponibil (vândut separat) în 40 psi 1 model PRF10040S. Filtrul de ecran de schimb (vândut separat) este modelul #: RBY-200SSMX. Rain Bird „Utilizarea inteligentă a apei”. DE LA PRODUCĂTOR Rain Bird Corporation este o companie privată fondată în 1933 în timpul boom-ului agricol din California. Suntem recunoscuți ca producătorul și furnizorul numărul 1 de produse și servicii de irigare din lume. Cu birouri de vânzări pe tot globul; oferim peste 4.000 de produse de irigare care economisesc apă în peste 130 de țări. Încă de la început, Rain Bird a produs și oferit cea mai largă gamă de produse de irigare de înaltă calitate din industrie pentru: ferme, terenuri de golf, arene sportive, dezvoltări comerciale și case. În ultimii 80 de ani, Rain Bird a primit peste 450 de brevete în întreaga lume. Inclusiv primul pentru irigare în 1935 pe aspersoarele noastre originale cu acționare cu impact (brevetul SUA nr. 1.997.901) care a revoluționat producția de alimente agricole și a inaugurat o nouă eră în irigații la nivel mondial. În 1990, acest aspersor cu impact original a fost desemnat un reper istoric de către Societatea Americană a Inginerilor Agricoli. Produsele noastre acoperă toate aspectele de irigare... temporizatoare/controlere, aspersoare rotative pop-up, aspersoare pop-up cu cap de pulverizare, duze de stropire, supape de irigare, irigare prin picurare, drenaj și multe altele. Aceste produse au fost alese și instalate la nivel mondial în cele mai mari și prestigioase proiecte de irigare rezidențială, comercială, agricolă și terenuri de golf. Rain Bird se angajează să utilizeze inteligentă a apei™, extinzându-se dincolo de produse la educație, formare și servicii pentru industrie și comunitate. Moștenirea noastră este să proiectăm și să fabricăm numai produse de cea mai înaltă valoare și calitate. Suntem recunoscători că am primit numeroase premii de recunoaștere de la mulți dintre partenerii noștri valoroși. Rain Bird „Utilizarea inteligentă a apei

Pentru utilizare cu unelte rotative care pot găzdui o dimensiune de tijă de 1/8. Ce este inclus: Bit de sculptat din carbură de tungsten 1/8 (x1). Forma cilindrică a frezei de sculptură permite îndepărtarea în profunzime a materialului, taie zone plate, margini rotunjite și face tăieturi de oprire și tăieturi în V. Ideal pentru proiecte precum gravarea pe metal sau pe sticlă, sculptură în piatră sau îndepărtarea blitz-ului din piese turnate. Bițile de sculptură cu carbură de tungsten extrem de durabile Dremel pot fi utilizate pentru aplicații mai agresive pentru modelarea, netezirea sau șlefuirea materialelor dure, cum ar fi metale, oțel călit, ceramică de foc, fontă, materiale plastice și lemn de esență tare. Importat. metalic.
Batteries Included? ‎No
Batteries Required? ‎No
Brand Dremel
Color ‎Silver
Customer Reviews 4.7 4.7 out of 5 stars 743 ratings 4.7 out of 5 stars
Included Components ‎Unit^Instruction Guide
Is Discontinued By Manufacturer ‎No
Item model number ‎9901
Item Package Quantity ‎1
Item Weight 10 Grams
Item Weight ‎0.353 ounces
Manufacturer ‎Dremel
Material Tungsten Carbide
Material ‎Tungsten Carbide
Measurement System ‎Metric
National Stock Number ‎3455-01-308-4389
Part Number ‎9901
Power Source ‎Corded-electric
Product Dimensions ‎1.6 x 0.8 x 0.2 inches
Size Pack of 1
Size ‎Pack of 1
Warranty Description ‎No

3.7

13 Review
5 Star
79
4 Star
13
3 Star
6
2 Star
1
1 Star
2

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu*

Scritto da: AJ
Did exactly what I needed it to.
I used it to widen a hole on tempered steel. Works great.
Scritto da: chris.w.
Cleared right through a steel bolt and aluminum casing.
Allowed me to "drill" out a sheared-off M6 bolt and enlarger the hole for a threaded repair insert. Cleared through the steel bolt and aluminum casing with minimal effort. Will buy it again when this one dulls out.
Scritto da: Pat
Great tool
Cuts very well doesn't break if used properly. I trimmed 1/8 inch steel with it no problems.
Scritto da: Lady Chozens~
Worked!
Perfect for my use!
Scritto da: Robert Retford
Quality tool
Quality tool at a good price
Scritto da: Benny
Good sharp cutter for mild steel but very brittle
I bought this cutter to make a square hole in a metal stud - the type of metal studs used to hold up drywall in high-rise apartments/offices. The cutter worked great, it moved through the metal stud no problem. I did however have 2 problems that I'm writing this review so that others can benefit from my experience: 1.) The cutter is relatively short. I was trying to cut metal that was behind some drywall. So the cutter had to be long enough to get through the drywall and through the metal. Because of an obstruction on the wall surface, I had to hold the tool about 1.25" away from the metal. This made it so that only the very tip of the cutter would contact the metal. While it worked I can comment that the tool is very short, so consider you application before buying. 2.) The cutter is very brittle. I actually cracked the shaft of this tool and could not complete my job. Because of my particular use, the cutter was bouncing around a bit in the slot I was cutting. This caused the bit to break. After it broke, i used the remaining portion to try to cut again. It broke a second time. Final recommendations: This cutter is good for controlled cuts in mild metals where you can brace/secure the work and the tool. This tool is not very good for free-hand cutting as I was doing. Make sure that you control the tool well to prevent bouncing and cracking of the bit. I think I will re-try with a thicker-shanked bit. Perhaps 3/8" if I can find one.
Scritto da: Lonewolf
Tungsten carbide endmill
Not much to say, they are endmills in Tungsten carbide. Dremel pricing is too high for tooling like this. Came loose bouncing around in a big box, one of the two I ordered was stuck in bottom flap, ready to fall out. Luckily I received both, was close call.
Scritto da: Barry Wagner
Finished the task
I needed to shape an opening I drilled in the end of a hand railing. I was slightly off center and just needed to round over a bit to center the peg. This bit was perfect for the job and did it well and quick. It easily worked its way through oak. Job done.
Scritto da: WellTrainedMonkey
Cuts hardened metal effortlessly.
I was working on turning an old bastard file into a knife and needed some way to add minor details on the handle. This got the job done and it still holds its edge. One slight disappointment is that I found a tiny chip on one of the cutting edge, but thankfully it does not appear to affect the overall performance. Just not sure at what point that happened. Amazing performance considering the cost. Great bit to have with your dremel. I'm very happy with this bit.
Scritto da: Mike
Quality product
Needed to enlarge coil seat hole in the lower control arms of my resto. This did the trick like butter in less than a minute per hole with my Dremel. I had my doubts before purchasing, but proved unwarranted. Very pleased. Good durable product. As advertised.
Scritto da: Salvador elizalde santos
Empaque resellado, posible engaño
Regrese el artículo, porque se notaba que había sido abierto, y resellado, la etiqueta de dremel la blanca que ponen estaba despegada hacia un lado, y el plastico del empaque se veía irregular de un lado, como que fue resellado por eso la regrese, no me gusta el engaño si desde el inicio explicaran que esta nuevo pero resellado podría haber accedido pero esto me parecía un engaño y eso molesta.
Scritto da: AdrianS
Warning: Made in China
I bought a couple of these, together with some 9904 bits. While the 9904's are made in the US, the 9901 have the dreaded "Made in China" printed on them. After my experience with Chinese "titanium coated" drill bits, I expect that they are no better than the regular multipurpose bits, but at least twice as expensive (which seems to be confirmed by reviews on amazon.com). If you want Chinese cutting bits, you can get them much cheaper elsewhere, instead of paying a premium just for the Dremel logo.
Scritto da: Jody Wright
Performance on metal
I used this cutter with my Dremel to remove excess metal on new door strikes mounted on metal door frames installed with new handles. Now the doors close and lock with perfection.

Produse asemanatoare

Descoperiți rețeaua noastră internațională

Expediem în 28 de țări, peste 200.000 de produse. Fii la curent, abonează-te la newsletter.

Array