Dispozitive de control-NC25-1UK002 Supapă de siguranță fără cod din alamă seria NC, interval de presiune reglabil 25-200 psi, 1/4 tată NPT

Name: Dispozitive de control-NC25-1UK002 Supapă de siguranță fără cod din alamă seria NC, interval de presiune reglabil 25-200 psi, 1/4 tată NPT
Brand: Control Devices
SKU: 0094700417541
Price: 145.51 RON
Availability: InStock

Brand:Control Devices

3.5/5

L
145.51

Această supapă de siguranță Control Devices NC25-1UK002 are un corp din alamă, o presiune de degajare reglabilă, o conexiune de intrare filetată 1/4 tată NPT, un inel O din silicon și un inel de tragere din oțel inoxidabil pentru reducerea manuală a presiunii. Corpul din alamă al supapei, scaunul supapei din alamă și arcul și bila din oțel inoxidabil rezistă la coroziune și pot fi utilizate la temperaturi de funcționare de până la 250 de grade F. Supapa poate fi reglată pentru a se deschide între 25 și 200 psi folosind șurubul de reglare moletat și blocare. nuci de dulceata. Această supapă de siguranță are un debit standard de 80 de picioare cubi pe minut (SCFM) și este potrivită pentru aplicații de reducere a presiunii la temperaturi înalte, cum ar fi compresoarele de aer. Deschiderile supapei permit fluidelor sau gazelor să scape pentru a scădea presiunea și apoi se închid odată ce supapa atinge limita presiunii de reașezare. De asemenea, eliberează excesul de vid prin deschiderea pentru a elibera un gaz în sistem și apoi închiderea după ce atinge limita de presiune scăzută. Unele supape de siguranță au un mecanism de reglare pentru a seta presiunea unde se deschide supapa, făcându-l potrivit pentru diverse aplicații. Supapele de siguranță sunt evaluate în funcție de volumul de lichid sau gaz care poate curge prin ele și materialul din care este construită supapa trebuie să fie potrivit pentru fluidul sau gazul, care poate fi corosiv sau la o temperatură extremă, în care funcționează. Supapele de siguranță sunt utilizate într-o varietate de aplicații, cum ar fi compresoarele de aer, producția petrochimică și chimică, procesarea gazelor naturale și generarea de energie. Control Devices produce supape și alte dispozitive de control al debitului. Compania, fondată în 1963, are sediul în Fenton, MO.

Cantitate

Adaugă in coş Cumpără acum

EAN: 0094700417541

Categorii Industriale și științifice, Casa și bucătărie, Cucătărie și sufragerie, Piese și accesorii pentru electrocasnice mici, Piese și accesorii pentru mașini de gătit sub presiune, Piese de schimb,

Inelul O din silicon asigură o etanșare etanșă până la 10% din presiunea stabilită. Temperatura maximă de 250 de grade F pentru utilizare în aplicații cu temperaturi ridicate. Construcție din alamă și arc din oțel inoxidabil pentru rezistență la coroziune. Conexiune de intrare filetată 1/4 tată NPT. Presiune de descărcare reglabilă de la 25 la 200 psi.

Brand	Control Devices
Country of Origin	USA
Domestic Shipping	Item can be shipped within U.S.
Exterior Finish	Stainless Steel, Brass
Inlet Connection Size	0.25 Inches
Inlet Connection Type	National Pipe Tapered
International Shipping	This item can be shipped to select countries outside of the U.S.
Is Discontinued By Manufacturer	No
Item Dimensions LxWxH	5 x 1 x 1 inches
Item model number	NC25-1UK002
Manufacturer	Control Devices
Material	Brass
Outlet Connection Type	MNPT
Product Dimensions	5 x 1 x 1 inches; 1.59 Ounces

5 Star

4 Star

3 Star

2 Star

1 Star

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu^*

Rating-ul tău

Scritto da: Woodchuck

Works perfectly

I bought a cheap pressure paint pot from Harbor Freight Tools and the pressure relief valve kept blowing at 30 psi. I bought this as a replacement and it works perfectly. It's very easy to dial in the exact pressure for which you need it to release.

Scritto da: Senpai!

Does what it's supposed to do.

Came with the blue 150-200psi spring installed, my 60gal compressor wants 140psi max, so I installed the smaller "gray" spring that is good for 100-150psi. Disabled my electric pressure shut off, ran the compressor up to 155 psi, then slowly backed off on the adjustment until it triggered as I had it too tight. I let it bleed pressure until it shut itself off, backed off the adjustment a little more, let the compressor fill the tank again and this valve released at exactly 150psi. Tightened down the locknut, enabled the electric cut off and tested again. My electric cutoff triggers at 140psi, it triggered like normal, I disabled it, let the compressor keep going, and this valve triggered as it should at 150psi. So all in all works as it should. Things to keep in mind below: It's a spring, so if you crank the adjustment knob all the way down you can completely compress the spring and it'll never release. This is the same as if you just blocked off the pressure relief entirely, so start with the adjustment only screwed in a little and adjust to raise the pressure. When it pops it'll bleed off about half the pressure needed to activate. Mine activates at 150psi, it'll stay open to bleed pressure until about 75psi. Yes, this is annoying, but it's not meant to be a pressure control, it's meant to be a safety valve to keep your tank from exploding and you from dying. I don't trust anything fully, so I'll test this on a monthly basis to ensure it still works as designed. Will update this review if any changes are needed or made.

Scritto da: E 2003 Tundra & 2000 ML320

Ajustable Pressure Relief Valve Review

This little PRESSURE RELIEF VALVE was ordered for an RO pressurized system as an extra safety backup in case the water pump pressure switch would fail and the pump would continue building unsafe pressure to the system to the point it would damage the system. There were absolutely no written Instruction in the package from the manufacture! I was lucky enough to have found a reviewer who actually mentioned what the water pressure range each springs represent below: manufacturer instructions: Yellow from 25-50 Red from 51-100 Silver from 101-150 Blue from 151-200 I ended up using the red spring, because It' s between the safe range of my water pressure system. The safe range that I needed is beyond 85 PSI for the relief valve to open and release the pressure until It safely got back to 80 PSI once again. To adjust the relief valve: 1) There are two nuts on top of it. First among the springs, decide which is the safe range your system should safely operate under. 2) Totally unscrew the top and put in the correct color spring intended to be used according to your system 3) For instance, I have used the Red Spring. Tightening down the top nut to increase the cut-in range between 51 PSI-100 PSI to where the relief valve will open. I was able to test it on my system until I was able to narrow it down to 85PSI where It would safely open up and release the pressure back to just 80 PSI. I took one star off, because there were no Instruction at all for the little thing!

Scritto da: Austin

Originally came misassembled, but easy to tune

If your valve is leaking under any pressure, check that the little plug is rubber side down when you trade out the springs. Overall, works well enough as a secondary safety measure. mine won't reset until the pressure gets to about 10 psi (set at 60) but its not a regulator, it's a safety relief

Scritto da: Gabriel Velazquez

Works Excellently Common Sense Required

I purchased this for an air compressor I bought which had an under-spec relief valve. This valve solved my problem, and I love that it is adjustable. Some common sense is required to put the valve together, it doesn't include any written instructions, but then again, if you do not understand how this valve works, and how to put it together, then perhaps you shouldn't be operating whatever it is that you are screwing this valve into. Hmm??? Regardless, adjusting the valve is as simple as squeezing the springs between your fingers. The softer the spring, the lower it's operating range. The springs are color coded so it is easy to identify them. Once you find the correct spring for the range you are seeking (in my case I needed the blue spring 100-200 PSI), it is as simple as dropping the spring in, and turning the adjusting knob until the valve attains the pressure you are seeking. In my example, I screwed in the knob about 3 turns, and cranked on my compressor. At about 100 PSI the valve discharged. I then screwed it in another 1.5 turns. The compressor shut off at it's operating pressure of 150 PSI. I slowly backed the knob off until the valve began to discharge air, and from there screwed it back in a half turn. Works great! Compressor reaches it's operating pressure, and connecting loads, and adjusting the feed regulator does not discharge the valve. I'm extremely pleased with both the valve and the compressor!

Scritto da: Cly Faker

Decent upgrade to a stock safety release.

When I first started dice making I decided to make myself a pressure pot using the (relatively) low cost paint tank conversion. After having the original safety valve trip when the tank hit just 20 PSI (and scaring the crap out of me in the process), I started looking around for a new one. I found this valve mentioned in one of the resin casting communities I frequent, and many months later I still have no complaints.

Scritto da: Amazon Customer

Lacking Documentation

This may be a great product, but it comes with ZERO documentation telling you what spring covers what pressures. Putting the wrong spring in a low pressure system could be catastrophic. Useless without documentation….