CURT 56189 Cablaj remorcă personalizat cu 4 pini, pentru Mitsubishi Outlander selectat, negru

Brand:CURT

3.4/5

L
461.28

Dacă vehiculul dumneavoastră nu este echipat cu cabluri pentru tractarea unei remorci, cablarea personalizată CURT este soluția ideală. Un cablaj personalizat -- numit și conector T -- este un dispozitiv electric simplu, plug-and-play, care se conectează la sistemul electric al autovehiculului și oferă o conexiune standard, universală de cablare a remorcii. Acest lucru se realizează folosind doi sau mai mulți conectori compatibili OEM specifici vehiculului pentru a se conecta la ansamblul farului din spate, eliminând nevoia de tăiere, îmbinare și lipire în timpul instalării. Cablurile personalizate sunt create pentru vehicule specifice și, deși nu sunt disponibile pentru toate vehiculele, oferă una dintre cele mai rapide, mai ușoare și mai sigure modalități de a cabla un vehicul pentru remorcare. Acest cablaj special furnizează un conector plat cu 4 căi și este proiectat pentru a fi un cablaj personalizat pentru a se potrivi în anumiți ani de Mitsubishi Outlander (pentru a verifica compatibilitatea vehiculului dvs., consultați informațiile despre aplicație). Vine cu toate componentele de cablare necesare pentru a stabili o conexiune fiabilă a cablajului remorcii, precum și un capac de praf pentru a menține conectorul curat atunci când nu este utilizat. Ai în minte o imagine a următoarei destinații -- poate că este barca care aterizează la locul tău preferat de pescuit, poate este un loc de campare care are vedere la una dintre capodoperele naturii sau poate este următorul mare șantier. Cu toate acestea, transformarea acelei imagini într-o realitate necesită mai mult decât visarea cu ochii deschiși. Este nevoie de o conexiune solidă și de cantitatea potrivită de putere. Cablajul personalizat CURT este realizat cu una dintre cele mai sofisticate tehnologii din industrie și este conceput pentru a fi instalat cu ușurință, oferindu-vă o conexiune electrică de lungă durată pentru configurarea cârligului de remorcare.

CAPACĂ DE PRAF. Pentru a promova utilizarea de lungă durată și rezistența la intemperii, acest cablaj cu 4 poli de iluminare a remorcii vine cu un capac de praf din cauciuc. Se potrivește cu ușurință pe conectorul plat cu 4 căi atunci când nu este utilizat, protejându-l împotriva elementelor exterioare. PUTERE DE FINE. Acest cablaj de remorcă cu 4 căi este construit cu tehnologie de montare pe suprafață. Acest tip de circuite generează mai puțină căldură, intensitate optimă a luminii și performanță durabilă. SPECIFICE VEHICULUI. Acest cablaj de piață de schimb, vehicul-remorcă, este proiectat pentru anumiți ani ai modelului Mitsubishi Outlander. CONECTOR STANDARD. Acest cablu de remorcă cu 4 plăci poate fi folosit pentru a conecta luminile spate ale remorcii, luminile de semnalizare de frână și semnalizatoarele de direcție. Cablajul luminii remorcii cu 4 căi este popular pe o varietate de remorci, adăugând opțiuni versatile de remorcare pentru vehiculul dumneavoastră. UȘOR DE INSTALAT. Fără tăiere! Fără îmbinare! Acest kit cablaj remorcă se conectează la cablajul existent din fabrică pe vehiculul dvs. și îl echipează cu un conector standard de cablare a remorcii cu 4 pini din spate pentru conectarea și tractarea unei remorci.
Brand CURT
Brand ‎CURT
Country of Origin ‎USA
Customer Reviews 4.3 4.3 out of 5 stars 118 ratings 4.3 out of 5 stars
Exterior ‎Painted
Is Discontinued By Manufacturer ‎No
Item Dimensions LxWxH 9 x 6 x 3 inches
Item model number ‎56189
Item Weight ‎1.4 pounds
Manufacturer ‎Curt Manufacturing
Manufacturer Part Number ‎56189
Material Rubber
Model ‎Custom Wiring
OEM Part Number ‎56189
Product Dimensions ‎9 x 6 x 3 inches

3.4

13 Review
5 Star
69
4 Star
13
3 Star
7
2 Star
3
1 Star
7

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu*

Scritto da: ABC
Working just fine.
For whatever reason, the original wiring harness for my trailer lights failed. I ordered this one to fit my car and I now have trailer lights again. Since I didn't have a place to work on the car, I had our local U-Haul install the wiring harness.
Scritto da: DOBY DADDY
not plug and play
I thought this is supposed to be plug and play. The power wire is not plug and play and needs to be ran under the carpet along the edge so door sill panels and center column lower trim panel need to be taken off. I didn't go through the firewall. I just plugged it into the fuse box under the dash. Also had to drill a hole in the rear floor pan above the spare tire so the spare tire had to be dropped. Whole thing took about an hour.
Scritto da: Rev DoPray
2018 Mitsubishi Outlander Phev Successful Install
I was able to install this into my 2018 Mitsubishi Outlander PHEV GT S-AWC. Everything was hooked up in the back without needing to run the wire under the car to the battery. I just hooked it up to the battery in the back. There also wasn’t a need for any trim/panel removal tools. The instructions were useless but I simply looked at the wiring diagram and installed it. Although I haven’t tested it with my trailer I am giving this product 5-Stars. If I run into difficulty with it functioning correctly I will update my review.
Scritto da: Asher04
Not for Vehicle that already has Factory Tow Package
Before you buy this product - check to see if your vehicle has the factory tow package included. To find out if you do, check the installation video from etrailer (for their product) and the installer will point out in the hood what you need to look for. If you do have the factory tow package go with the model #56296 (ignore the vehicle fit from Amazon: it will say it will not fit your vehicle). Only go with this product if you don't have the factory tow package. I didn't realize I had the factory tow package until I went through the installation steps.
Scritto da: Jana M. Kleffman
Worked Great
Did what it said it was gonna do. Took about 30 minutes to install, nothing complex. Make sure you have the ability to lift your vehicle because you are going to need to crawl along the ground a bit to get the wire up to the front of the vehicle. Not a big issue with ramps. Overall, good kit.
Scritto da: Jason Brinckmann
Watch my video for Installation!!!!
The media could not be loaded. Everything you need and not too terrible to install yourself! Watch my detailed video for a complete overview on the installation because the instructions page that it comes with (-1 star) has incomplete written directions and the photos only show the panel removing in the trunk.
Scritto da: Moises Pimentel
To connect it’s on the driver side left side thank you
It fits perfectly on the video it shows on the right side of the rear end of the 2018 outlander but on the outlander it will be on the left rear of the light fixture the only thing that was different but it works perfectly fine thank you
Scritto da: TLB
Works great
Works great on my three row 2019 Mitsubishi Outlander. Easy to setup even though I had to crawl under my car to run the wire to the engine bay. Electrical tape helps keep the connectors attached to the wires.
Scritto da: Martin Thomas
Good quality and very nice custom fit
Easily plugs into lighting system for a professional installation.
Scritto da: John
No wires to splice
2015 outlander . Easy plug-ins. No cut wires , so if electrical problems come up later you can unplug harness and start trouble shoot the vehicle only . - Routing wire too frount of vehicle can be done with no drilling but a little of a challenge if you are not a young man ????
Scritto da: Amazon Customer
Easy install and working fine
I purchased and installed myself following instructions from YouTube. It's working great.
Scritto da: Gary wilkinson
Excellent and on time
Scritto da: Jim B.
Good for a 2019 Mitsubishi outlander phev
Used this on a 2019 Mitsubishi outlander phev worked great.

Produse asemanatoare

Descoperiți rețeaua noastră internațională

Expediem în 28 de țări, peste 200.000 de produse. Fii la curent, abonează-te la newsletter.

Array