CURT 31198 Cârlig receptor frontal de 2 inchi, Toyota Land Cruiser selectat, Sequoia, Tundra

Name: CURT 31198 Cârlig receptor frontal de 2 inchi, Toyota Land Cruiser selectat, Sequoia, Tundra
Brand: CURT
SKU: 0612314311989
Price: 2140.27 RON
Availability: InStock

Brand:CURT

3.6/5

L
2140.27

INSTALARE USOARA. Acest cârlig de tractare față este proiectat cu un design specific vehiculului pentru a se potrivi modelelor selectate de Toyota Land Cruiser, Sequoia și Tundra. REZISTENT LA COROZIUNE. Pentru o protecție superioară împotriva ruginii, ciobirii și daunelor UV, acest cârlig frontal este acoperit cu un strat dublu de strat A rezistent la rugină, care acoperă cârligul în interior și în exterior și un strat de pulbere neagră foarte durabil. CONSTRUCȚIE TESTATE. Acest cârlig cu montare frontală este complet testat pentru siguranța dumneavoastră la unitatea noastră de inginerie din Detroit. Testăm modelele noastre de cârlig de remorcă față conform specificațiilor SAE J684. FORTA DE FINE. Acest cârlig frontal este evaluat pentru 5.000 lbs. GTW și 500 lbs. greutatea limbii. De asemenea, este evaluat pentru 9.000 de lbs. capacitate de tragere în linie dreaptă pentru aplicații de remorcare și troliu de recuperare (limitată la componenta de remorcare cu cea mai mică valoare). RECEPTOR VERSATIL. Adăugați un receptor de cuplare util în partea din față a vehiculului dvs. cu acest cârlig de receptor cu montare frontală. Receptorul standard de 2 inchi vă permite să atașați un plug de zăpadă, un suport de marfă, un suport pentru biciclete, un cârlig de remorcare, un suport pentru troliu sau alt accesoriu de remorcare.

Cantitate

Adaugă in coş Cumpără acum

EAN: 0612314311989

Categorii Automotive, Accesorii exterioare, Produse de tractare și trolii, Atelaje, Receptoare,

Brand	CURT
Brand	‎CURT
Customer Reviews	4.5 4.5 out of 5 stars 224 ratings 4.5 out of 5 stars
Exterior	‎Black Powder Coat
Finish Type	GLOSS BLACK POWDER COAT
Is Discontinued By Manufacturer	‎No
Item model number	‎31198
Item Weight	‎25.4 pounds
Manufacturer	‎Curt Manufacturing
Manufacturer Part Number	‎31198
Material	Carbon Steel
Model	‎Front Mount Hitch
OEM Part Number	‎31198
Product Dimensions	‎44 x 15 x 7 inches
Vehicle Service Type	Marine-Personal-Craft, Van, Sport-Utility-Vehicles, Truck, Trailer

5 Star

4 Star

3 Star

2 Star

1 Star

Scrie o recenzie

E-mailul dvs. nu va fi publicat. Toate câmpurile obligatorii sunt marcate cu^*

Rating-ul tău

Scritto da: Ken M.

Perfectly on 2019 Toyota Sequoia

I received it yesterday and put it on today. It fit perfectly on my 2019 Toyota Sequoia. I may have lost about 1 inch of ground clearance. But, I don't see how they could have designed it any higher up. It looks like a factory install. Also, it is designed with spacing to allow reinstallation of my existing tow loops. I am very pleased.

Scritto da: Maria

Product looks good and heavy duty

Product looks very well made but as far as packaging! goes I think they used monkeys to pack it for them box was 3 times its size with no protection! also product came with no instructions luckily I’m a little handy so I can figure it out

Scritto da: Sheridan J. Engel

The hitch is well designed and fits perfectly.

The hitch fit perfectly and only took about 15 minutes to install. Just remove the two front tow hooks and install the hitch with the tow hooks.

Scritto da: Dan Tomlinson

Fits Well, but a couple of notes.

This is the second Curt Front Mount Receiver I have installed on a vehicle. As was the case with the first one, the receiver is well-built and nicely finished. The instructions were accurate and easy to follow. The installation went quickly on my 2014 Toyota Tundra Double-cab. There are two reasons I didn't give this five stars. First, if your truck has a skid plate installed, you must either remove it or modify it so that you can change the oil filter without removing the skid plate, presumably because it would be difficult if not impossible to remove it once the receiver is mounted. The receiver instructions mention this and tell you where to cut. The 4" round cut involves more than sheet metal. Some of the support framing must also be cut. I chose, for the time being, not to reinstall the skid plate as I don't intend to do any hard core off-roading. The second issue is the distance the receiver is set-back from the front bumper. I measured 6.5" from the front of the license plate mount to the face of the receiver. This means that some hitch tubes may not be long enough to properly seat into the receiver. There are hitch extenders should this be an issue.

Scritto da: gene hale

Tucked out of the way nicely, made very stout, I am satisfied

No dislikes, will be used for surffishing rack

Scritto da: jrwebster

Good Quality. Good Fitment.

Asking price was higher than comparable units, but Curtis quality is notable. Would buy CURTIS again. (( ...But wait for a more appropriate price point. )) Did get this one as "open box" discount. There's not much that could go wrong with heavy metal like this, and other than being dusty, there was NO damage, or even scuff marks. Didn't even look as if any attempt had been made to mount it. Happy with the product and purchase.

Scritto da: Teresa H.

Will not fit without added trimming

Instructions are vague and had I known the scope of the work necessary to make it work I wouldn't have ordered it. The 1st is the diagram for the skid plate cut-out to access the oil filter once the hitch is installed. The diagram has the cut-out in the wrong location. Second issue is that the front edge of the skid plates and splash shields will need to be cut for it to fit. Too much cutting for a "supposed to fit" part going on an $85,000 vehicle. It design is fine although the. reach of he receiver will likely require a longer hitch/ball assembly.

Scritto da: Scott Frakes

As promised, but should come with longer bolts

Fits perfectly, goes in really easy using a floor jack to support and align. If you have the TRD aluminum skid plate (1/4 inch thick), the stock bolts are too short when you add in the hitch. Head to the hardware store for longer bolts (bolts 1/2 inch longer worked fine). The actual installation was less than 30 minutes.

Scritto da: BR

easy to installl

Super easy to bolt onto my 2011 Sequoia. Maybe one hour at most. Haven't actually used it yet but did test the bike mount and all fit well, just have been using my rear hidden hitch at the moment.

Scritto da: Dave

Good fit

Need to trim skid plate for oil filter changes. Have not done a change with this on yet.... will see how hard it is.

Scritto da: Captain G

Fits and works as advertised.

Arrived faster than expected. Fit perfectly. My garage installed in under 20 minutes (on a hoist with air ratchet) as advertised, and my mechanic was impressed too.

Scritto da: Rob

Great

Perfect fit 09 tundra. Make a hole in your oilpan for future oil changes if you dont wanna pull the front hitch off every time

Scritto da: Sharon McMahon

as described

As described